Also, look in your local yellow pages. Carpet stores sometimes have bamboo flooring that comes in bamboo rods that you could use. [1] X Research source
Make sure that the bamboo has at least one node – a notch where it is solid inside instead of hollow like the other parts of the bamboo. It’s usually marked by circular ridges that look like joints on the bamboo. One node at the end of the flute will become what is known as the “cork. ” The node should be smooth and without holes on the inside or the outside so that the flute has proper tone. [3] X Research source
Make sure that the bamboo has at least one node – a notch where it is solid inside instead of hollow like the other parts of the bamboo. It’s usually marked by circular ridges that look like joints on the bamboo. One node at the end of the flute will become what is known as the “cork. ” The node should be smooth and without holes on the inside or the outside so that the flute has proper tone. [3] X Research source
Make sure that the bamboo has at least one node – a notch where it is solid inside instead of hollow like the other parts of the bamboo. It’s usually marked by circular ridges that look like joints on the bamboo. One node at the end of the flute will become what is known as the “cork. ” The node should be smooth and without holes on the inside or the outside so that the flute has proper tone. [3] X Research source
The piece of bamboo that you selected might have several nodes. If it’s a long piece of bamboo, select the part of the bamboo that you are going to work with and sand down that section so you don’t sand the entire bamboo stem unnecessarily.
For instance, if you want a 14 inch flute, the nodes should be a little more than 7 inches (178mm) apart from each other. In other words, there should be a little more than 7 inches (178mm) of tube between each node. The aim is to cut it so that there is a node at the end and another node more or less in the middle. You want the flute to have a node at one end and another more or less in the middle after you cut it to size. It should have at least one. Wrap a piece of masking tape around the area that you want to cut, then cut it with the hacksaw. The tape helps stop the bamboo from splintering. Cut outside of the node. Don’t cut into it.
For instance, if you want a 14 inch flute, the nodes should be a little more than 7 inches (178mm) apart from each other. In other words, there should be a little more than 7 inches (178mm) of tube between each node. The aim is to cut it so that there is a node at the end and another node more or less in the middle. You want the flute to have a node at one end and another more or less in the middle after you cut it to size. It should have at least one. Wrap a piece of masking tape around the area that you want to cut, then cut it with the hacksaw. The tape helps stop the bamboo from splintering. Cut outside of the node. Don’t cut into it.
For instance, if you want a 14 inch flute, the nodes should be a little more than 7 inches (178mm) apart from each other. In other words, there should be a little more than 7 inches (178mm) of tube between each node. The aim is to cut it so that there is a node at the end and another node more or less in the middle. You want the flute to have a node at one end and another more or less in the middle after you cut it to size. It should have at least one. Wrap a piece of masking tape around the area that you want to cut, then cut it with the hacksaw. The tape helps stop the bamboo from splintering. Cut outside of the node. Don’t cut into it.
For instance, if you want a 14 inch flute, the nodes should be a little more than 7 inches (178mm) apart from each other. In other words, there should be a little more than 7 inches (178mm) of tube between each node. The aim is to cut it so that there is a node at the end and another node more or less in the middle. You want the flute to have a node at one end and another more or less in the middle after you cut it to size. It should have at least one. Wrap a piece of masking tape around the area that you want to cut, then cut it with the hacksaw. The tape helps stop the bamboo from splintering. Cut outside of the node. Don’t cut into it.
Another option is to burn out the nodes with a hot poker, but the safest option is most likely boring out the nodes with a long drill bit.
The diameter is the length of a circle.
The diameter is the length of a circle.
The diameter is the length of a circle.
Input your measurements of the flute’s inner diameter and wall thickness. Then, choose the key you want the flute to be in. If you cut your flute to a specific length for a specific key, you can skip this step if you want. The application will calculate the diameter for the embouchure and the other holes in the seven-note Western scale. Write down the diameters of each hole. [4] X Research source For instance, suppose the diameter of the blow hole is 10mm (0. 393 inches), then according to the calculator, the diameter of the following finger holes 1-7 might be 8. 0mm(0. 3149 inches), 8. 5mm (0. 335), 9mm (0. 354 inches), 7mm (0. 275 inches) , 9. 5mm (0. 374 inches) ,10mm (0. 393), 5. 5mm (0. 217 inches).
When you’re drilling, hold the bit perpendicular to the bamboo with a steady hand. If you hold the drill at an angle or are unsteady as you drill, you might drill the bamboo improperly or splinter, crack or rip the bamboo. Be deliberate but careful as you drill.
When you’re drilling, hold the bit perpendicular to the bamboo with a steady hand. If you hold the drill at an angle or are unsteady as you drill, you might drill the bamboo improperly or splinter, crack or rip the bamboo. Be deliberate but careful as you drill.
When you’re drilling, hold the bit perpendicular to the bamboo with a steady hand. If you hold the drill at an angle or are unsteady as you drill, you might drill the bamboo improperly or splinter, crack or rip the bamboo. Be deliberate but careful as you drill.
When you’re drilling, hold the bit perpendicular to the bamboo with a steady hand. If you hold the drill at an angle or are unsteady as you drill, you might drill the bamboo improperly or splinter, crack or rip the bamboo. Be deliberate but careful as you drill.
When you’re drilling, hold the bit perpendicular to the bamboo with a steady hand. If you hold the drill at an angle or are unsteady as you drill, you might drill the bamboo improperly or splinter, crack or rip the bamboo. Be deliberate but careful as you drill.
Make sure your holes are marked in a straight line. Drill in successively larger bits, which means start with the smaller bits to make a starter hole. Then, slowly increase to the larger bits to get to the size drill bit to make the appropriate size. Some parts of the bamboo and thinner than other such as where a branch was growing. So, be mindful of this when you’re drilling. If you have to drill a hole over a node, this area will be thicker than other areas. Take your time and drill slowly.
